Specification:
Model |
B2002FR-8I-CM-TM-L06 |
Hardware |
|
Processor |
Dual Core Processor(Hi3516D V300)+ 1G memory + 16G flash |
Operating system |
Linux Operating system |
Storage |
Support TF card storage in the future ( only hardware interface reserved) |
Viewing angle |
Vertical viewing angle: 30°; Horizontal viewing angle: 30° |
Sensor |
1/2.8" Progressive Scan CMOS(IMX307) |
Lens |
6mm |
Speaker |
voice playback content can be customized |
Temperature measurement performance |
|
Measurement Environment |
16℃ - 40℃ (Indoor without wind, please refer to the end of the file) |
Temperature measurement Lens |
European original lens |
Sensors type |
Infrared Thermopile Medical-grade European imported sensors |
Measurement accuracy |
±0.2℃ |
Temperature resolution |
0.1℃ |
Temperature measurement distance |
≤40cm |
Measurement response time |
300ms |
Performance |
|
Recognition height |
1.2~2.2 meters, angle adjustable |
Recognition distance |
0.3~1.5 meters, depends on lens |
Recognition time |
Less than 0.2 seconds |
Storage capacity |
160,000 capture records |
Face capacity |
24000pcs |
Screen brightness |
≥400 cd/m2 |
Interface |
|
Switching output |
1 way switch output, other GPIO port can be customized |
Network interface |
1 RJ45 10M / 100M adaptive Ethernet port, Gigabit Ethernet port can be customized |
Wiegand interface |
1ch Wiegand interface input/output |
RS485 |
There is an RS485 interface on the PCB board, but no lead |
USB interface |
1ch USB interface |
Camera |
|
Camera |
Dual cameras |
Effective pixels |
2MP, 1920*1080 |
Min Illumination |
Color 0.01Lux @F1.2(ICR);B/W 0.001Lux @F1.2 (ICR) |
SNR |
≥50db(AGC OFF) |
WDR |
120db, ISP algorithm face partial exposure |
Resolution |
Main Stream: 50HZ: 25fps (1920*1080,1280*720) 60HZ: 30fps (1950*1080,1280*720) |
Sub Stream: 720*576, 1-25(30)fps; 640*480, 1-25(30)fps; 320*240,1-25(30)fps; |
|
Function |
|
Web side configuration |
support |
remote upgrade |
support |
Regular |
|
Working humidity |
0~90% relative humidity, no condensation |
Salt spray |
level Rp6 or above |
Antistatic |
contact ±6KV, air ±8KV |
Powered |
DC12V/2A |
Device power |
20W(MAX) |
Column aperture |
36mm |
Equipment size |
252 (L) * 136 (W) * 26 (T) mm |
Screen size |
8 inches IPS HD screen |
Weight |
1.7 kg |
Interface:
No. |
Name |
Quantity |
Remark |
1 |
Network |
1 |
RJ45 |
2 |
Power |
1 |
DC12V IN |
3 |
USB |
1 |
USB 2.0 |
4 |
Switch Output |
1 |
Switch output interface A+/B- |
5 |
Wiegand protocol input interface |
1 |
① D0 ② D1 |
6 |
Wiegand protocol output interface |
1 |
① vcc12V ② GND ③ D0 ④ D1 |
7 |
RS485 |
1 |
① 485- ② 485+ |
Attention:
1. The temperature measuring device should be used in a room with no ventilation and room temperature between 16 ℃ -40 ℃.
2. The temperature measurement accuracy will affect if people entering indoors from a cold outdoor environment.
3. Please warm the temperature measuring device up for 10 minutes before testing.
4. Please make sure that there is no heating source or air conditioning vent within 3 meters of the device.
5. Please taking temperature after leaving the forehead unobstructed for three minutes indoors when the temperature is stable.
6. Please do not exposure forehead under the situation such as showers, hair dryers, sprays, etc. It will affect the measurement.
7. The forehead temperature will be lower than the actual temperature if there is oil on the forehead, makeup, oxygen mask, or wrinkles in the elderly.
8. Please make sure there is no hair or clothing covering the area where the projection is located.